Moisture Meters Models

The Checkline CP-425 Calibration Electrode is designed for calibration verification of the TMT-425 moisture meter. The kit includes two (2) calibration electrodes, one preset at approx. 22% the other at approx. 44%. The reference value is indicated on the label. To operate, simply insert one of the calibration electrodes into the electrode holder, turn on the TMT-425 and set the calibration curve to "Test Block". The display should match the value printed on the label of the calibration electrode. The calibration electrodes interlock for convenient storage

Please click on the links below for additional information on the models available for this product:

The DeFelsko CMMIS16PK PosiTector CMM IS Expansion Pack, 16 Pack is comprised of 16 CMM IS probes, 16 Saturated Salt Solutions, 16 Calibration Check Chambers, 16 Caps, 40 coin cell batteries.

Please click on the links below for additional information on the models available for this product:

The DeFelsko CMMIS1PK PosiTector CMM IS Expansion Pack, 1 Pack is comprised of 1 CMM IS probes 1 Saturated Salt Solutions 1 Calibration Check Chambers 1 Caps 2 coin cell batteries

Please click on the links below for additional information on the models available for this product:

The DeFelsko CMMIS4PK PosiTector CMM IS Expansion Pack, 4 Pack is comprised of 4 CMM IS probes, 4 Saturated Salt Solutions, 4 Calibration Check Chambers, 4 Caps, 10 coin cell batteries

Please click on the links below for additional information on the models available for this product:

DeFelsko CMMISKITB PosiTector CMM IS In Situ Concrete Moisture RH Meter, Basic Kit is compraised of 3 CMM IS probes, 3 Saturated Salt Solutions, 3 Calibration Check Chambers, 3 Caps, Extraction Tool, Tape Measure, Ten A-76/LR-44 coin cell batteries. PosiTector CMM IS probes and free mobile app guide users through the ASTM F2170 documentation criteria. View and record readings directly with your Apple or Android smart device or PosiTector DPM Advanced gage.

Please click on the links below for additional information on the models available for this product:

DeFelsko CMMISKITC PosiTector CMM IS In Situ Concrete Moisture RH Meter, Complete Kit is comprised of 5 CMM IS probes, 5 Saturated Salt Solutions, 5 Calibration Check Chambers, 5 Caps, Extraction Tool, Tape Measure, Vacuum Tool Attachments, Ten A-76/LR-44 coin cell batteries, Hard shell carrying case. Easily collect and report measurements in conformance with ASTM F2170.

Please click on the links below for additional information on the models available for this product:

DeFelsko CMMISKITP3-E PosiTector CMM IS In Situ Concrete Moisture RH Meter, Pro Kit is comprised of PosiTector DPM3 Advanced, 5 CMM IS probes, 5 Saturated Salt Solutions, 5 Calibration Check Chambers, 5 Caps, Extraction Tool, Tape Measure, Vacuum Tool Attachments, Ten A-76/LR-44 coin cell batteries, Hard shell carrying case. Easily collect and report measurements in conformance with ASTM F2170.

Please click on the links below for additional information on the models available for this product:

Delmhorst 1235 Electrode for Hay Moisture Meter is used for testing standard bales. Attaches directly to the connector on top of the meter. Also available in 18 length as 1235/18.

Please click on the links below for additional information on the models available for this product:

The Delmhorst 26-ES 2-Pin Electrode is used by flooring installers. The 496 contact pins that come with the Delmhorst 26-ES 2-Pin Electrode penetrate 1 1/8 and have insulated shanks so that only the tips are exposed. The pins make contact only at their uncoated tips and provide much more accurate readings of moisture content at various levels of penetration. This feature is useful for a variety of different applications.

Please click on the links below for additional information on the models available for this product:

The Delmhorst 496 Replacement Moisture Pin is insulated except at the tips, and measure 2" overall with 1 1/8" penetration. Standard on the 26-ES, and can be used to check wood up to 5" thick.

Please click on the links below for additional information on the models available for this product:

The Delmhorst 608 Replacement Moisture Pins is used on roofing, insulation, timber, poles, and EIFS. The pins measure 4" overall, and penetrate 3 1/4". Standard on 21-E and 18-ES electrodes, Also available in 7 length with 6 penetration as 608/001.

Please click on the links below for additional information on the models available for this product:

The Delmhorst BD-10 Analog Moisture Meter for Building Inspection is used to measure moisture in wood and other non-wood building materials is easy to operate and easy to read. For those who prefer an analog display, the Delmhorst BD-10 moisture meter is a great alternative to the digital BD-2100. The Delmhorst BD-10 is a great entry level meter, and is ready to go with a single button press!

Please click on the links below for additional information on the models available for this product:

The Delmhorst BD-2100 Digital Moisture Meter for Building Inspection is great for measuring moisture in a variety of different building materials, including wood, concrete, drywall, EIFS, roofing, insulation, and flooring. The Demlhorst BD-2100 moisture meter has a digital display, an adjustable alarm, and Delmhorsts exclusive calibrated drywall scale.

Please click on the links below for additional information on the models available for this product:

The Delmhorst C-2000 Digital Moisture Meter for Cotton is used for effectively measure moisture content, ensuring high-quality cotton every time. The instrument features four separate scales for testing lint cotton, seed cotton, wool and viscose/rayon.

Please click on the links below for additional information on the models available for this product:

The Delmhorst F-2000 Digital Moisture Meter for Hay is great for hay producers looking to enhance quality control. The Delmhorst F-2000 moisture meter checks hay moisture in the windrow or in bales, and comes with the same accuracy and clarity as the FX-2000!

Please click on the links below for additional information on the models available for this product:

The Delmhorst F-2000 Digital Moisture Meter for Hemp is ideal for hemp producers looking to enhance quality control. The Delmhorst F-2000 has the versatility to check hemp in its various forms.

Please click on the links below for additional information on the models available for this product:

The Delmhorst F-2000T Tobacco Moisture Meter is ideal for tobacco growers. The Delmhorst F-2000T shares many of its features with the F-2000 hay meter. Calibrated for Burley tobacco, the Delmhorst F-2000T moisture meter is just what you need to produce a high-quality crop every time.

Please click on the links below for additional information on the models available for this product:

The Delmhorst F-6/6-30 Analog Moisture Meter for Hay is a great entry-level meter for value-minded hay producers. The Delmhorst F-6/6-30 moisture meter is also a favorite among those serving the export markets that require lower MC range readings.

Please click on the links below for additional information on the models available for this product:

The Delmhorst FX-2000 Digital Moisture Meter for Hay is ideal for high-volume producers who need the time-saving convenience of on-the-go monitoring. Whether in the windrow, on-the-go while baling, or in the bale, the Delmhorst FX-2000 moisture meter gives clear, accurate moisture readings every step of the way!

Please click on the links below for additional information on the models available for this product:

The Delmhorst G-34 Hops Moisture Meter is ideal to check moisture levels in baled hops to assure high-quality harvest and safe storage. The large analog display and built-in battery check make this a favorite among hop growers worldwide

Please click on the links below for additional information on the models available for this product:

The Delmhorst G-7 is a rugged resistance-type meter, great for testing the moisture content of grain at harvest time and while in storage. The integral double-disc electrode cup holds only 3-4 grams, allowing for more uniform sampling and providing accurate and repeatable readings. You can even attach optional accessories to check moisture in bulk material and hay. The G-7 also provides useful statistics on stored readings

Please click on the links below for additional information on the models available for this product:

The Delmhorst G-79 is designed specifically to read a wide range of moisture on gypsum. One of our first meters to feature our exclusive gypsum scale, the G-79 is still a favorite for its large analog display and classic design.

Please click on the links below for additional information on the models available for this product:

The Delmhorst GB-1 Gypsum Sensor Blocks for Soil Moisture Meter are made of gypsum, cast around two concentric, stainless steel electrodes. They are manufactured under controlled conditions to obtain a maximum degree of uniformity and fast response to soil moisture changes. The Delmhorst GB-1 measures 7/8 dia. x 1 1/8 in height. It is the most widely used sensing unit, easy to install and especially suited for extensive sampling of soil at various depths.

Please click on the links below for additional information on the models available for this product:

The Delmhorst HT-3000 thermo-hygrometer moisture meter is a great tool for monitoring the level of humidity in flooring installations, building inspections, restoration jobs, and even agriculture operations. With a simple interface, fast acclimation, and useful statistics like dewpoint and grains per pound, the Delmhorst HT-3000 moisture meter is a great value at an economical price. Use the HT-3000 in conjunction with one of our moisture meters for a thorough assessment of every job.

Please click on the links below for additional information on the models available for this product:

The Delmhorst HT-4000F moisture meter is a stand-alone thermo-hygrometer for flooring installers and inspectors. The Delmhorst HT-4000Fs detachable sensor makes the Delmhorst HT-4000F moisture meter ideal for testing a concrete slab according to the ASTM F2170 standard. It has the same fast acclimating RH/T sensor found in our popular TotalCheck 3-in-1 moisture meter. For flooring contractors who prefer having separate meters to one combination meter, the HT-4000F is the perfect solution.

Please click on the links below for additional information on the models available for this product:

The Delmhorst J-2000 Digital Pin-Type Wood Moisture Meter is ideal for flooring contractors, woodworkers, furniture manufacturers, QC inspectors and small mills. The Delmhorst J-2000 wood moisture meter helps to keep up with ever-changing job conditions. With built-in wood species correction and temperature correction, along with storage and informative reading statistics the Delmhorst J-2000 is an extremely versatile tool at a great value.

Please click on the links below for additional information on the models available for this product:

The Delmhorst J-4 Analog Wood Moisture Meter is a user-friendly meter that youll pick up with ease, but never want to put down! The Delmhorst J-4 Wood Moisture Meter is a tried and true solution for installers, woodworkers, and small shops.

Please click on the links below for additional information on the models available for this product:

The Delmhorst J-Lite Moisture Meter is a great all-around tool for any situation! Whether you're experienced or just starting out, you can't go wrong with the Demhorst J-Lite moisture meter! With J-Lite's unique LED display, you'll be in the know no matter where the job takes you.

Please click on the links below for additional information on the models available for this product:

The Delmhorst JL-2000 digital leather moisture meter is the perfect quality control tool for tanneries everywhere. Dont leave the quality of your product to chance. Check moisture content with the Delmhorst JL-2000 leather moisture meter.

Please click on the links below for additional information on the models available for this product:

The Delmhorst KS-D1 Digital Soil Moisture Tester is used with the GB-1 Gypsum Sensor Blocks to monitor the soil moisture available to the plants. This system eliminates guesswork, so that irrigation can be effectively scheduled, according to plants' requirements

Please click on the links below for additional information on the models available for this product:

The Delmhorst NAVPRO Navigator Moisture Meter Pro is ideal to check moisture in drywall, insulation, wood, concrete, and plaster. It traces leaks to find exterior moisture and dry rot. Meeting the restoration contractor's demand for detailed, accurate, and accessible information. The Delmhorst Navigator Pro easy to use 3-in-1 meter offers pin mode, scan mode, and thermo-hygrometer in a single handheld unit. The Navigator Pro also features advanced job definition that organizes readings of the floor, wall, and ceiling in affected rooms. Stored readings can be downloaded to a spreadsheet on your PC, providing clear, complete documentation of every job. With features you can't find anywhere else, plus Delmhorst's renowned quality and service, the Navigator Pro will guide you from wet to dry.

Please click on the links below for additional information on the models available for this product:

The Delmhorst P-2000 Digital Pin Type Paper Moisture Meter is an electrical resistance-type moisture meter, utilizing the relationship between moisture content and electrical resistance. The contact pins mounted on the top of the meter are used for making direct contact with the material. Various external electrodes are also available for specific applications. The Delmhorst P-2000 Moisture Meter is especially useful for testing paperboard, corrugated stock, and paper tubes. It is ideal for plant superintendents, inspectors, buyers, and sales people.

Please click on the links below for additional information on the models available for this product:

The Delmhorst PROSCAN Pinless Wood Moisture Meter is a non-invasive pinless moisture meter for flooring installers, lumber manufactures, woodworkers and building inspectors who want to quickly find moisture in wood products and a variety of building materials. The non-invasive meter is made in the USA and uses radio frequency signals to quickly scan wood, drywall, concrete or other building materials without damaging the sample. Its built-in species corrections for woods with a specific gravity between .30 and .80, makes checking a variety of wood species a cinch. With ProScan professionals can work with confidence, save time, stay on budget and avoid call-backs.

Please click on the links below for additional information on the models available for this product:

The Delmhorst QuickNav Moisture Meter is an easy to use 3-in-1 meter that offers pin mode, scan mode, and thermo-hygrometer in a single handheld unit. The Delmhorst QuickNav will instantly calculate dewpoint, grains per pound (GPP) and vapor pressure for fast, accurate moisture measurement. The Delmhorst QuickNav offers the same high performance pin mode, scan mode, and thermo-hygrometer as our industry leading NavigatorPro, in an easier to use format. If you are looking for the versatility of a 3-in-1 meter and do not need to store and download reading, QuickNav is the answer.

Please click on the links below for additional information on the models available for this product:

The Delmhorst RC-1E Wood Moisture Meter is used to measure moisture in gypsum using a three-range scale: (0.2%-1%, 1%-8%, and 8%-50%). Clad in a durable and beautifully finished hardwood case, the RC-1Es classic design and wide moisture measurement range make it a valuable addition to your toolkit. The RC-1E has been a favorite among dry kiln operators for years.

Please click on the links below for additional information on the models available for this product:

The easy-to-use 2-in-1 Delmhorst TechCheck PLUS is designed with simplicity in mind and helps to make even the most demanding job simple. The newly updated Delmhorst TechCheck PLUS moisture meter has all the great features you've come to expect, along with some new ones. Given the challenging conditions of building inspection, installation, and drying jobs, it pays to have an easy-to-use moisture meter that you can depend on.

Please click on the links below for additional information on the models available for this product:

The Delmhorst TechScan Pinless Moisture Meter is a fast, accurate, non-destructive way to check for moisture in walls and floors. Save time, and work with confidence, with the Delmhorst TechScan. It's the next generation of pinless moisture meters designed for restoration professionals, flooring installers, and home inspectors. The right diagnostic tools are a must when addressing water damage, testing sub and top floors to ensure similar % moisture content, or assuring a home buyer of structural integrity before purchase. The Delmhorst TechScan pinless moisture meter make it easy to find moisture hot spots and narrow down areas affected by moisture. Use it as a stand-alone tool or with our pin-type moisture meter for further precise diagnosis.

Please click on the links below for additional information on the models available for this product:

The Delmhorst TM-100 Moisture Meter is an instrument that features rugged construction to withstand even the toughest work conditions offering years of use. Delmhorst brings its characteristic quality and support to temperature monitoring. Not only does this device monitor temperature in the air, it can also take temperature readings inside of various building materials with the use of special Delmhorst electrodes such as the TS-102 Sensor

Please click on the links below for additional information on the models available for this product:

The Delmhorst TotalCheck 3-in-1 meter is used to measure moisture by pin and scan modes, and is fast acting, accurate, thermo-hygrometer. The removable RH sensor measures ambient temperature and RH, and calculate dew point and GPP. High levels of ambient humidity can be a warning sign at inspection jobs. RH is also a major concern when testing a concrete sub-floor. To address this concern, the Delmhorst TotalCheck moisture meter is designed to conform to the ASTM F-2170 standard to determine RH in a concrete slab using in-situ probes. Using TotalCheck to follow the ASTM F-2170 will provide useful information to minimize moisture-related flooring problems and failures.

Please click on the links below for additional information on the models available for this product:

The Humimeter BG2 Silage Moisture Meter is especially designed for measuring the moisture content of plants for biogas production and is ideal for suppliers of silage, plant manufacturers as well as researchers. The instrument comes as a complete kit with a digital display for easy readout of measured values.

Please click on the links below for additional information on the models available for this product:

The Humimeter BL2 Universal Biomass Moisture Meter is specifically-designed for users who require a portable moisture meter to cover a wide range of biomass applications. It is supplied with both the insertion probe for wood chips, wood pellets and sawdust as well as the hammer Probe with short and long pins for measurement on round timber, split logs and hay and straw bales. The BL2 is supplied with several calibration curves that are automatically activated when a specific probe is connected. If more than one calibration is offered for the connected probe, it can be user-selected using the menu system. Measuring results are displayed instantly and are temperature compensated.

Please click on the links below for additional information on the models available for this product:

The new BLH Wood Shaving Moisture Meter is specifically designed for the accurate measurement of Moisture Content of wood shavings. The BLH provides a measuring resolution of 0.1% and is supplied with five (5) built in calibrations for the following species of wood types: Beech, Birch, Spruce, Pine, Poplar and Oak. The BLH is supplied with built-in memory for 10,000 values and features automatic temperature compensation for the highest possible accuracy. It also includes USB Output and is supplied with a data transfer cable and free PC-Software. A hand-wheel system is provided to compress the 400 ml sample into the measuring container to get highly repeatable results which is shown on the over-sized LED display in seconds. The BLH is battery powered using four (4) AA-Batteries providing maximum convenience and portability for use everywhere. It is constructed for trouble-free use even in the toughest field applications.

Please click on the links below for additional information on the models available for this product:

The BLL Wood Chip Moisture Meter with Insertion Probe is a precision instrument that accurately measures the moisture content in Wood Chips with our BLL meter. One meter long insertion probe for easy measurement in deep piles of chips. The BLL is supplied with three (3) separate calibration curves, depending upon the physical makeup of the wood chips to measured. There are defined into the following classes as described in the European Standards as; Wood Chips, Coarse WC and Industry WC.

Please click on the links below for additional information on the models available for this product:

The Humimeter BLO Online Moisture Measuring System is a precision instrument that allows an easy online determination of the water content of wood chips and similar materials. The wood chips sensor for the installation in a screw conveyor can easily be integrated also in existing plants. With this system you can actuate your dryer or oven optimally according to the water content. Therefore the efficiency of your oven can be improved and accordingly the energy consumption of drying can be reduced. The water content and the temperature is shown on the well-lit LC display of the analyzing device. The connection to a control system can be realized by the 4-20mA analog output. As the BLO for wood chips is already completely calibrated, the installation can be realized with a modicum of effort. In order to avoid very costly mistakes due to incorrect moisture levels, you have to check the moisture of material in the manufacturing and treatment process to give you the chance to take suitable measures in time. More than 40.000 customer-specific solutions have been designed and produced for industry and university institutions. Our technicians provide reliable support and are available to answer your questions and solve your technical problems.

Please click on the links below for additional information on the models available for this product:

The Humimeter BLW Timber Moisture Meter is ideal for operators of biomass heating systems, wood suppliers and buyers of round and split logs. It is integrated calibration curves for various wood types are included allowing the BLW to display measurements directly in "Moisture Content", eliminating the need to refer to separate "look-up tables. This insures the highest possible accuracy with minimum effort and reduces the chances of errors.

Please click on the links below for additional information on the models available for this product:

The Humimeter BMA Biomass Moisture Meter is a professional moisture meter for determination of water content, bulk density and ATRO tons for suppliers and operators of heating plants using biomass. For measuring wood chips, barks, wooden pellets, elephant grass, wood shavings, sawdust and corn cobs.

Please click on the links below for additional information on the models available for this product:

The Humimeter BMC Wood Chip Moisture Meter is a highly accurate moisture meter with automatic bulk density compensation for quick determination of water content of wood chips, barks, wooden pellets, elephant grass, wood shavings and sawdust. The entire measurement procedure is extremely easy & only takes seconds. Simply turn on the gauge, collect the desired Biomass test sample and pour into storage bin and view the water content (%-moisture) on the large backlit LCD display. The Humimeter BMC and BMC-USB models both include a built-in datalogger for storage of 10,000 values. The BMC-USB model ads USB data output for downloading stored data to a PC with software included at no additional charge. Both models include the possibility to program and store three (3) custom calibrations if one of the factory-supplied calibration is not sufficient to produce desired results.

Please click on the links below for additional information on the models available for this product:

The Humimeter BP1 Wood Pellet Moisture Meter is ideal for measuring water content in wood pellets; thistle, straw, rape elephant grass, etc. Ideal for fast and easy measurement without prior treatment of the samples. It is delivered with digital scale, plastic case, measuring cup and batteries.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS1 Compact Grain Moisture Meter is ideal for measurement of small volumes, the sample size of the FS1 is 100ml. Because of its small size, the FS1 is ideal for field tests on the farm. The automatic temperature compensation ensures accurate measurements. Quickly and easily measure moisture of maize, rye, triticale, wheat, barley, oats, rape, peas, soybeans, horse beans, sunflower seeds and rice.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS2 Grain Moisture Meter is a whole grain moisture meter with a sample of 300g for accurate and repeatable measurements. The FS2 is equipped with automatic temperature compensation ensuring correct calculation of moisture content. The FS2 whole grain moisture meter is ideal for use in farming, trade, laboratories and animal feed production. Quickly and easily measure moisture of all grain types including maize, rye, triticale, wheat, barley, oats, rape, peas, soybeans, horse beans, sunflower seeds and rice.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS3 Food / Grain Moisture Meter is ideal for fast and easy determination of water content of peeled and unpeeled raw coffee, roast and ground coffee, cocoa beans, poppy seeds, rape, pumpkin seeds, peas, soybeans, scarlet runner beans, wheat, peeled, unpeeled and brown rice, linseed, sesame, sorghum and buckwheat.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS4 Grain, Fruit, Beans & Seeds Moisture Meter is a special model moisture meter that can be calibrated by the user on their specific fruit or grain. The FS4 grain and fruit moisture meter is a new and revolutionary powerful portable water content measuring instrument. The FS4 has a high accuracy and measures a sample of 300g easily without prior treatment of the products. Suitable for all grain types and finished products. For use in farming, trade, seed growing, research, laboratories and the food in animal feed industries. The grain moisture meter is suited for measuring of maize, rye, triticale, wheat, spelt, barley, oats, rape, pumpkin seeds, peas, soybeans, beetle beans, horse beans, sunflower seeds, rice, raw coffee and poppy seeds. As a helpful extra the gauge features a calibration curve and customer calibrations for own products.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS4-1 Sludge Moisture Meter is used to determine the moisture content of part dried and full dried sewage sludge-granulate. A new revolutionary high-capacity series equipped with an innovative sensor technology for measuring water content. The FS4-1 is delivered as a complete kit including: Measuring gauge, digital scale, carrying case, measuring cup supplied in carrying case.

Please click on the links below for additional information on the models available for this product:

The Humimeter FS4-2 Universal Material Moisture Meter is a Universal Moisture Meter that can be custom calibrated on the customer's material. FS4-2 is equipped with USB data output and calibration function for self-calibration on many materials. The entire measurement procedure is extremely easy & only takes seconds. Simply turn on the gauge, collect the desired test sample and pour into storage bin and view the water content (%-moisture) on the large back-lit LCD display. The Humimeter FS4-2 includes built-in memory for 10,000 values with serial output downloading data to external printer, PC-Software or 3rd-Party accounting programs for automatic calculation of price or payment. Additionally, the FS4-2 is supplied with PC Software, Transfer Cable, USB Converter, Digital Scale, Cup, a Protective Case and batteries.

Please click on the links below for additional information on the models available for this product:

The Humimeter FSG Food and Special Product Moisture Meter is calibrated for spiral noodles, peanuts and walnuts and more. Users can generate and store their own custom calibration curves or upon request, this service can be provided at an additional cost. For factory generation of custom calibration curves, a 4-5 litre sample must be supplied. When paying for products from suppliers, it is normally important to measure the moisture content to insure suitable product quality and to insure that you are paying a fair price, not paying for the weight of water. Operation of the Humimeter FSG Food and special products moisture meter is quick and easy. Simply turn-on to FSG, ll it with your sample and the FSG will display the moisture content on the backlit LCD Display. The measuring values can be stored in the built-in memory.

Please click on the links below for additional information on the models available for this product:

The Humimeter HUMI-WIRELESS Wireless Data Transmission Kit for Moisture Meters is used as a cable-free transfer of data from BM2/BLL to Laptop/PC or printer. Plug-n-Play design does not require any USB drivers for communication. Can be added in the field if desired.

Please click on the links below for additional information on the models available for this product:

The Humimeter LM6 Portable Leather Moisture Meter, USB Output, 3% to 65% is designed to quickly and easily determine the water content of different types of leather. The LM6 measures moisture non-destructively, measurements are taken by placing the instrument on the material with the back-side. The moisture percentage and temperature appear on the display within a few seconds.

Please click on the links below for additional information on the models available for this product:

The Humimeter MCT-HS Hay and Straw Moisture Meter is ideal for measurement of water content in hay and straw bales with fixed 0.6 meter (23.6 inch) stabbing probe. Includes temperature compensation for highest possible accuracy. Supplied with two separate built-in calibrations; one for Hay and the 2nd for Straw (also used for Miscanthus).

Please click on the links below for additional information on the models available for this product:

The Humimeter P2 Paper Moisture Meter is primarily for Kraft paper, packaging paper and paperboard. Quick and highly accurate measurement using a non-destructive method! Just place the instrument on the paper's surface and the moisture content will be displayed. Quick and cost saving paper moisture measurement.

Please click on the links below for additional information on the models available for this product:

The Humimeter RH1 Digital Relative Humidity Meter is a precision instrument that measures climate humidity easily, fast and accurately with the RH1 relative moisture meter, optionally available with a PC-interface, software and printer.

Please click on the links below for additional information on the models available for this product:

The Humimeter RH2 Relative Humidity Meter is a precision instrument that measures relative humidity, absolute humidity, dew point, equilibrium moisture content and AW value.

Please click on the links below for additional information on the models available for this product:

The Humimeter RH5 Paper Moisture Meter is specifically designed for measuring moisture content in paper by inserting the "sword probe" into a stack/pile of paper. The measured values can be manually entered into data logger or can be set to automatically record at pre-set intervals The temperature is measured as well and included in the hygromeasurement. Temperature range for measurement is -10 to +60 C and can either be displayed in C or F. The RH5 hygrometer can measure the moisture content in paper or alternatively be used to measure relative air humidity measurements or dew point. An optionalUSBOutput moduleis available for transferring recorded data to a PC or printer for analysis/documentation. It is supplied with FREE software, a data link cable for connection to a PC and printer, and a USB adapter. There is also an option for a thermal printer with which you can print you measured values without a PC directly from the instrument.For additional protection, we recommend the optional protection sleeve (p/n RH5-SLEEVE) available to prevent the sensor or gauge being damaged during the "insertion" process. A sleeve removal tool is also recommended.

Please click on the links below for additional information on the models available for this product:

The Humimeter RH6 Paper Moisture Meter is also ideal for automatic monitoring of climate in printing rooms and paper storage rooms. The instrument is equiped with a temperature compensated paper and wood moisture content equilibrium and calibration curves for determination of water content.

Please click on the links below for additional information on the models available for this product:

The Humimeter RP6 Moisture Meter for Recycled Paper is designed for fast, non-destructive measurement of moisture content in recycled paper and for the detection of moisture spots in recycling paper bales. The RP6 features can be extended with an optional air humidity and temperature sensor in order to measure environmental parameters quickly and efficiently.

Please click on the links below for additional information on the models available for this product:

The Schaller PM5 Paper Moisture Meter is ideal for paper manufacturers, paper processors and paper retailers, for a non-destructive determination of absolute moisture of paper and cardboard at warm, running paper rolls as well as at stagnant, cool rolls. With non-contact infrared paper temperature measurement. Non-destructive measurement through the packaging.

Please click on the links below for additional information on the models available for this product:

The Schaller PMP Moisture Meter for Paper is ideal for uses on paper piles and non-rotating paper rolls. For quality control of paper processors like printing houses, paper retailers and corrugated paper manufacturers. Measuring instrument for determination of absolute water content of paper and solid cardboard in piles or on a non-rotating roll of paper.

Please click on the links below for additional information on the models available for this product:

The AZ 8703 is a pocket sized digital hygrometer provides fast and accurate measurement of relative humidity, temperature and dew point of the environment.

Please click on the links below for additional information on the models available for this product:

The Tramex BSIK5.1 Building Survey Inspection Kit is comprised of the multifunctional Tramex MRH III digital moisture meter allowing for non-invasive testing of moisture conditions in numerous building materials such as drywall, wood, plaster, brick, ceramic tiles, resilient flooring, laminates and roofing. The MRH III and reusable relative humidity probe allow for testing relative humidity, temperature and dew point in the environment. When used in conjunction with the infrared surface thermometer, detrimental condensation conditions conducive to microbial growth can also be identified. The heavy-duty pin-probes measure moisture content in wood, and the insulated 7 pins allow for deep wall cavity probing. Concrete slab relative humidity testing to ASTM F2170 can also be performed with reusable relative humidity probes and hole liners (optional).

Please click on the links below for additional information on the models available for this product:

The Tramex BSIZK5.1 Building Survey Inspection EZ Kit is a complete kit. The Tramex BSIZK5.1 features the multifunctional Tramex MRH III digital moisture meter allowing for non-invasive testing of moisture conditions in numerous building materials such as drywall, wood, plaster, brick, ceramic tiles, resilient flooring, laminates and roofing. The MRH III and reusable relative humidity probe allow for testing relative humidity, temperature and dew point in the environment. The heavy-duty pin-probes measure moisture content in wood, and the insulated 7" pins allow for deep wall cavity probing. Concrete slab relative humidity testing to ASTM F2170 can also be performed with reusable relative humidity probes and hole liners (optional).

Please click on the links below for additional information on the models available for this product:

The Tramex CALCRH is used to easily verify if moisture meters yield proper moisture readings, or if or needs to be sent to a calibration lab.

Please click on the links below for additional information on the models available for this product:

The Tramex Calibration Check Box is a simple tool used to check the calibration of Tramex moisture meters.

Please click on the links below for additional information on the models available for this product:

The Tramex CIK5.1 Concrete Inspection Kit is a complete kit for testing concrete moisture per ASTM F2659 & ASTM F2170. The Tramex CIK5.1 features the Tramex CMEX II moisture meter and Tramex Hygro-i2 relative humidity probes. The Concrete Inspection Kit comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex CME4 Concrete Moisture Meter Encounter is used to measure moisture content instantly in concrete floors and sand. The Tramex CME4 Concrete Moisture Meter Encounter is a hand-held electronic moisture meter utilizes non-destructive impedance measurement for moisture determination. Parallel co-planer electrodes are mounted on the unit's base which transmit low-frequency signals into the concrete or cement floor to a depth of approx. 1/2 inch (12.5 mm). The results give the average moisture content to a depth of approximately 4 inches (100 mm) during the drying period. While concrete under normal conditions can never be completely dry, the instrument has been calibrated on acceptably dry material. It compares the change in impedence caused by the presence of water and displays moisture content on an analog dial. The meter is calibrated to give percentage moisture content readings on a clean, bare dust free concrete floor slab, thus readings taken on concrete slabs through paint, coating, adhesives or other materials on the surface of the slab should be regarded as qualitative or comparative and no quantitative.

Please click on the links below for additional information on the models available for this product:

The Tramex CME5 Concrete Moisture Encounter is a non-destructive meter for measuring moisture content instantly in concrete slabs per ASTM F2659 and giving comparative or equivalent readings in other cementitious floor screeds. Easy-to-use, giving precise and repeatable results, the Concrete Moisture Encounter allows the user to make multiple tests over a large area in the shortest possible time.

Please click on the links below for additional information on the models available for this product:

The Tramex CMEX2 CMEXpert II Concrete Moisture Encounter Expert is designed for the instant and precise measurement of moisture content in concrete and other floors and screeds. Incorporating plug-in ports for the optional Hygro-i relative humidity probe and heavy-duty pin-type wood probe, this moisture meter transforms into the ideal all-in-one instrument for the flooring professional. The Tramex CMEX2 detects and evaluates the moisture conditions within the slab or screed by non-destructively measuring the electrical impedance. A low frequency electronic signal is transmitted into the material under test via the electrodes in the base of the instrument. The strength of this signal varies in proportion to the amount of moisture present in the material. The Tramex CMEX2 CMEXpert II Concrete Moisture Encounter Expert CMEX II determines the strength of the current and converts this to a moisture content value for concrete slabs and a comparative value for other cementitious floor screeds, displayed on a large clear digital dial.

Please click on the links below for additional information on the models available for this product:

The Tramex CMEX5 Concrete Moisture Encounter X5 is a non-destructive digital multi moisture meter for concrete floors and slabs providing instant and precise quantitative measurement of moisture content using Gravimetric testing as a baseline. The Tramex CMEX5 Concrete Moisture Encounter X5 also provides Carbide Method equivalent readings for concrete and other cementitious substrates as well as comparative readings as per ASTM F2659. Incorporating plug-in ports for the optional Hygro-i2 relative humidity probe testing per ASTM F2170 and heavy-duty pin-type wood probes, this moisture meter transforms into the ideal all-in-one instrument for the flooring professional.

Please click on the links below for additional information on the models available for this product:

The Tramex CMK5.1 Concrete Inspection Mater Kit is a complete kit for testing per ASTM F2659 and ASTM F2170. The Tramex CMK5.1 comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex CZK5.1 Concrete Inspection EZ Kit is a compact kit for testing moisture in concreteperASTM F2659 & ASTM F2170featuring the TramexCMEX IImoisture meter and TramexHygro-i2relative humidity probes. TheConcrete Inspection EZ Kitcomes in a protective Tramex Easy-travel case.

Please click on the links below for additional information on the models available for this product:

TheTramex Dec Scanner is a mobile non-destructive moisture detection instrument on four wheels, which allows for quick scanning of large roof areas with instant, accurate results. The Dec Scanner detects and evaluates the moisture conditions within roofing systems by non-destructively measuring the electrical impedance. A low frequency electronic signal is generated, transmitted into the material under test via one of the two electrodes incorporated in the rubber electrode mat, and received by the second electrode. The strength of this signal varies in proportion to the amount of moisture in the material under test. The Dec Scanner determines the strength of the current and converts this to a comparative moisture content value. By moving the Dec Scanner across a roof surface in a regular pattern, a continuous reading is obtained, and areas that contain moisture can be readily identified.

Please click on the links below for additional information on the models available for this product:

The Tramex EIK5.1 Exterior Insulation Finishing Systems (EIFS) Inspection Kit is a complete kit featuring the TramexRWS Roof and Wall Scanner(a combination of the Wet Wall Detector and the Leak Seeker) for instant, non-destructive evaluation of moisture conditions deep within Exterior Insulation and Finishing Systems (EIFS). The EIFS Inspection Kitincludes the TramexMRHIIImoisture and humidity meter, a pin-type resistance probe and aHygro-i relative humidity probe to provide the ideal solution for measurement of ambient relative humidity, temperature and dew point, determination of moisture conditions in a variety of wall materials, sheathing and wood studding of EIFS systems, as well as in-depth readings of the moisture conditions of the substrate.

Please click on the links below for additional information on the models available for this product:

The Tramex FBSK5.1 Feedback Datalogger Starter Kit is designed and developed by Tramex for professionals who depend on accurate, reliable readings using the very best, state of the art technology and performing ASTM F2170. The Feedback DataLogger and App log up to 100,000 data point entries for relative humidity, temperature, dew point and grains per pound, transmitted wirelessly via Bluetooth BLE technology to your mobile device. On the App you can visualize Live Readings, Thermal Conditions and Psychrometric Charts, as well as creating and exporting spreadsheets, charts and reports. The Tramex Feedback DataLogger requires the Tramex Feedback Data Logger App and a compatible iOS or Android mobile device.

Please click on the links below for additional information on the models available for this product:

The Tramex FBZK5.1 Feedback Datalogger EZ Kit is designed and developed by Tramex for professionals who depend on accurate, reliable readings using the very best, state of the art technology and performing ASTM F2170. The Feedback DataLogger and App log up to 100,000 data point entries for relative humidity, temperature, dew point and grains per pound, transmitted wirelessly via Bluetooth BLE technology to your mobile device. On the App you can visualize Live Readings, Thermal Conditions and Psychrometric Charts, as well as creating and exporting spreadsheets, charts and reports. The Tramex Feedback DataLogger requires the Tramex Feedback Data Logger App and a compatible iOS or Android mobile device.

Please click on the links below for additional information on the models available for this product:

The Tramex FIK5.1 Flooring Inspection Kit isused for moisture testing of concrete and wood flooring to ASTM and other international standards. The Tramex FIK5.1 features the Tramex CMEX II digital concrete moisture meter for testing per ASTM F2659 and 3 best in class reusable Hygro-i relative humidity probes for testing relative humidity, temperature and dew point in the environment, or performing ASTM F2170 and ASTM F2420 (with optional Hood) for relative humidity readings in concrete slabs. An infrared surface thermometer is included for testing surface temperatures and can be used in conjunction with the Hygro-i probe to monitor dew point conditions. A heavy-duty hammer pin-probe allows the user to measure the moisture content in wood. Calibration check salts are included in the Flooring Inspection Kit, which comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex FMK5.1 Flooring Master Inspection Kit is the ultimate kit for pre- & post-application moisture testing of concrete slabs, wood and various other floor covering materials. The Tramex FMK5.1 features the Tramex CMEX II digital concrete moisture meter for testing per ASTM F2659 and 3 best in class reusable Hygro-i relative humidity probes for testing relative humidity, temperature and dew point in the environment, or performing ASTM F2170 and ASTM F2420 (with optional Hood) for relative humidity readings in concrete slabs. An infrared surface thermometer is included for testing surface temperatures and can be used in conjunction with the Hygro-i probe to monitor dew point conditions. A heavy-duty hammer pin-probe allows the user to measure the moisture content in wood. Also featuring a Tramex MRH III incorporating wood species calibration and temperature correction to accurately read the moisture content non-invasively in a variety of wood species and moisture conditions instantly and non-destructively in roofing, masonry, drywall and laminate. The MRH III can be used with optional Pin-type probe attachment for wood, and the relative humidity Hygro-i probe. Calibration check salts are included in the Flooring Inspection Master Kit, which comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex FZK5.1 Flooring Inspection EZ Kit is a compact kit for instant and accurate moisture testing of concrete and wood Flooring. The Tramex CMEX II digital moisture meter allows the user to non-invasively test concrete per ASTM F2659 and for testing relative humidity, temperature and dew point in the environment, or performing ASTM F2170 (and ASTM F2420 with optional Hood) for relative humidity readings in concrete slabs. The Tramex heavy-duty wood pin-probe measures the moisture content of wood. The Flooring Inspection EZ Kit comes in a Tramex Easy-travel case.

Please click on the links below for additional information on the models available for this product:

The Tramex HA21SP52 Hammer-action Pin-type Electrode is used with CMEX II, MRH III, Professional

Please click on the links below for additional information on the models available for this product:

The Tramex HH14SP200 Heavy-Duty Electrode with Cable and 7" Long Pins is used with CMEX2, MRH3 & PTM

Please click on the links below for additional information on the models available for this product:

The Tramex HPW Hole Punch is used for creating pilot holes for long pin probes in EIFS & Roofing Systems.

Please click on the links below for additional information on the models available for this product:

The Tramex Hygro-i Probe (Pack of 1) with Electronic Interface is used to connect to CMEX2 & MRH3 non-destructive moisture meters the Hygro-i probe provides measurements of humidity, temperature and dew-point in structural materials such as concrete flooring, walls etc. as well as the environmental conditions within the building structure allowing the user to perform in-situ & hood type RH testing to comply with ASTM F2170 & F2420.

Please click on the links below for additional information on the models available for this product:

The Tramex hole liner is used with Tramex Hygro-i relative humidity sensors. Used when performing ASTM F2170 in situ RH testing of concrete floors and slabs.

Please click on the links below for additional information on the models available for this product:

The TramexHygro-i2Relative Humidity probe is the most advanced and resilient RH probe on the market today. Used in conjunction with the TramexCMEX2orMRH3non-destructive moisture meters theHygro-i probe provides measurements of humidity, temperature and dew-point in structural materials such as concrete flooring, walls etc. as well as the environmental conditions within the building structure allowing the user to perform in-situ & hood type RH testing to comply withASTM F2170&F2420.

Please click on the links below for additional information on the models available for this product:

The Tramex IAQK5.1 Indoor Air Quality Kit is a complete moisture and humidity testing kit. The Tramex IAQK5.1 Indoor Air Quality Kit features the multifunctional Tramex MRH III digital moisture meter allowing for non-invasive testing of moisture conditions in numerous building materials such as drywall, wood, plaster, brick, ceramic tiles, resilient flooring, laminates and roofing. The Tramex IAQK5.1 Indoor Air Quality Kit and reusable relative humidity probe allow for testing relative humidity, temperature and dew point in the environment. When used in conjunction with the infrared surface thermometer, detrimental condensation conditions conducive to microbial growth can also be identified. The heavy-duty pin-probes measure moisture content in wood, and the insulated 7" pins allow for deep wall cavity probing.

Please click on the links below for additional information on the models available for this product:

The Tramex IRT2 hand held, infrared surface thermometer is a precision instrument that features a laser target pointer to gain instant readings on almost any surface from a distance.

Please click on the links below for additional information on the models available for this product:

TheIRTXis a hand held, infrared surface thermometer features a laser target pointer to gain instant readings on almost any surface from a distance.

Please click on the links below for additional information on the models available for this product:

The Tramex ME5 Moisture Encounter is a Dual-Depth, non-destructive moisture meter for instant moisture measurement and evaluation. Wood Moisture Content: 5 to 30%, Deep Depth penetration up to 1.25" (30mm) & Shallow Depth penetration up to 0.40" (10mm). 5 Ranges of sensitivity: Wood & Timber / Shallow Depth / Drywall & Roofing / Plaster & Tile / Masonry, making the Moisture Encounter ideal for testing in and through a wide range of materials in the building envelope.

Please click on the links below for additional information on the models available for this product:

The Tramex MEP Moisture Encounter Plus is a non-destructive overall building inspection moisture meter based on Impedance measurement which has applications for numerous industries. The Tramex MEP Moisture Encounter Plus Moisture Meter has many unique features that make moisture measurement and evaluation fast, precise and versatile. The Tramex MEP Moisture Encounter Plus detects and evaluates moisture conditions within various building materials by non-destructively measuring the electrical impedance. A low frequency electronic signal is transmitted into the material via the electrodes in the base of the instrument. The strength of this signal varies in proportion to the amount of moisture in the material under test. The Tramex MEP determines the strength of the current and converts this to a moisture content value, displaying it on a large clear analog dial. The Tramex CME is used and trusted by generations of professionals worldwide.

Please click on the links below for additional information on the models available for this product:

The Tramex MRH III Moisture and Humidity Meter is a electronic impedance moisture meter for non-destructive measurements (Moisture testing of wood, drywall, masonry, roofing and other construction materials) The small pocket size make this hand held gauge ideal for use in different industries, e.g. flooring, indoor air quality, water restoration, pest control, inspection/surveying. The parallel co-planar electrodes on the base transmit a low-frequency signal into the material under test. For carrying out a test, simply hold the the MRH-3 to the surface. The MRH-3 can be used on wood, plaster / brick, tiles and plasterboard (drywall). The gauge has plug-in ports for optional probes.

Please click on the links below for additional information on the models available for this product:

The Tramex PCK5.1 Pest Control Professional Kit is a complete moisture and humidity testing kit for the Pest Control Professional. The Tramex PCK5.1 features the TramexMRH IIIMoisture and Humidity Meter, allowing for non-destructive testing of multiple building material types, as well as pin type testing to identify Moisture Content in wood and wall cavities, and aHygro-i Relative Humidity probe for identifying areas of high relative humidity, both ambient and in existing cavities, that may be conducive to wood destroying organisms. ThePest Control Professional Kitcomes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex PTM2.0 Professional Pin Type Moisture Meter is a hand-held, digital, pin-type resistance moisture meter designed to take precise measurements of moisture content in wood, relative drywall readings and comparative WME (Wood Moisture Equivalent) readings in wood by-products and other building products. The Professional Tramex PTM 2.0 has built-in standard calibrations, specific calibration for over 500 wood species and adjustable temperature correction. When wood and wood by-products are installed at the correct moisture content for the environment in which they will be used, the risk of swelling or shrinkage is minimized. If it is installed too wet and dries in service the result will be shrinkage and distortion. If it is installed too dry it could gain moisture, which could result in swelling. Using a good quality moisture meter is the most practical way of ensuring the wood is at the correct moisture level for its intended use. Knowing the actual moisture level also enables efficient processing to be carried out, such as milling, machining, gluing, laminating, spraying and hand painting. The Professional PTM 2.0 fulfills all these requirements. The Professional PTM 2.0 moisture meter works on the principle of DC resistance. When the electrode pins are pressed or driven into the wood, the electrical resistance between the electrodes is measured. If the wood is dry, the resistance is high. If moisture is present in the wood the electrical resistance between the pins changes. The higher the moisture content the greater the reduction in resistance. The level of resistance is accurately measured by the instrument, which translates it into a moisture value. This is a percentage of dry weight moisture content for wood; comparative drywall reading values; and a WME (Wood Moisture Equivalent reference) value for many other building materials.

Please click on the links below for additional information on the models available for this product:

The Tramex PTMCALSET is a set of 3 calibration check plugs for Professional & Compact resistance meters.

Please click on the links below for additional information on the models available for this product:

The Tramex PTMMK5.1 Professional Wood Master Kit is a kit for instant and accurate measurement of moisture content in a large range of wood species, relative drywall readings and comparative WME (Wood Moisture Equivalent) readings in wood by-products and other building materials. The Tramex PTMMK5.1 features the Tramex Professional PTM2 with its built-in pins, a handheld heavy-duty pin probe and a handheld heavy-duty hammer pin probe, the Professional Wood Master Kit comes in a Tramex protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex PTMZK5.1 Professional Wood EZ Kit is ideal for instant and accurate measurement of moisture content in a large range of wood species, relative drywall readings and comparative WME (Wood Moisture Equivalent) readings in wood by-products and other building materials. The Tramex PTMZK5.1 features the Tramex Professional PTM2 with its built-in pins, a handheld heavy-duty pin probe and a handheld heavy-duty hammer pin probe, the Professional Wood Master Kit comes in a Tramex protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The TramexHygro-iElectronic Interface is used to connect the Hygro-i toCMEX2, WME&MRH3non-destructive moisture meters. TheHygro-iprobe provides measurements of humidity, temperature and dew-point in structural materials such as concrete flooring, walls etc. as well as the environmental conditions within the building structure allowing the user to perform in-situ & hood type RH testing to comply withASTM F2170&F2420.

Please click on the links below for additional information on the models available for this product:

The Tramex RHIH is a strong, robust insulated surface humidity hood tester for concrete floors and floor screeds. To be used in conjunction with the Tramex CMEXpertII or Tramex MRHIII to corroborate the non-destructive moisture content test.

Please click on the links below for additional information on the models available for this product:

The Tramex RHP-LW Hygro-i 320mm Long RH Probe is used with MRH III & CMEX II

Please click on the links below for additional information on the models available for this product:

TheTramex RIK5.1 Roof Inspection Kit is ideal for non-destructive checking of moisture conditions in roofing and waterproofing systems up to approximately 4 inches in depth, as well as non-destructive measurement of moisture conditions in concrete decks, wood decks and ambient relative humidity & dew-point conditions. The Tramex RIK5.1 Roof Inspection Kit features the handheld TramexRWS Roof and Wall Scannernon-invasive impedance scanner and the TramexCMEX IIelectronic moisture meter andHygro-i relative humidity probe. This kit comes in a protective, heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex RMK5.1 Roof Master Kitis the complete kit for the roofing professional, allowing for continuous and point-of-contact, non-destructive surveying of moisture conditions in roofing and waterproofing systems up to 6 inches in depth, as well as non-destructive measurement of moisture conditions in concrete decks, wood decks and ambient relative humidity & dew-point conditions.The Tramex RMK5.1 Roof Master Kit features the TramexDec Scanner, a mobile non-destructive impedance scanner,the handheld TramexRWS Roof and Wall Scannernon-invasive impedance scanner and the TramexCMEX IIelectronic moisture meter andHygro-irelative humidity probe. This kit comes in a protective, heavy-duty wheeled carry case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex RWS Roof and Wall Scanner is a multi-mode non-invasive impedance scanner designed for the instant, precise and non-destructive evaluation of moisture conditions and leak tracing in roofing per ASTM D7954 and in wall systems of the building envelope. The Roof & Wall Scanner detects and evaluates the moisture conditions within roofing and wall systems by non-destructively measuring the electrical impedance. A low frequency electronic signal is transmitted into the material under test via the electrodes in the base of the instrument. The strength of this signal varies in proportion to the amount of moisture in the material under test. The Tramex RWS Roof & Wall Scanner determines the strength of the current and converts this to a comparative moisture content value, displaying it on a large clear analog dial. Operating procedure: Moisture detection testing can be done at the time of installation, as part of an ongoing maintenance program, or prior to reparation of damaged roofing and wall systems. The RWS is a handheld, hardwearing instrument with dual operating modes for roofing and EIFS/Foam insulation systems, each with two ranges of signal penetration. Having calibrated the RWS on a known acceptably dry area, the RWS gives instant readings for the moisture survey.

Please click on the links below for additional information on the models available for this product:

The Tramex SAL75 Calibration Salt Check is designed to produce a 75% RH environment within the chamber which may be used to ensure the calibration of the Hygro-i RH probe is optimum.

Please click on the links below for additional information on the models available for this product:

The Tramex SMP Skipper Plus Marine Moisture Meter is a non-destructive moisture meter for the marine industry. The Tramex Skipper Plus non-destructive moisture meter provides a complete, safe method for detecting excess moisture in GRP and wooden boats. Three scales of sensitivity allow moisture detection in salt or fresh water. Moisture can cause peeling and blistering of applied finishes and treatments, newly applied finishes can fail prematurely if the wood it is applied to is not sufficiently dry. Hidden or trapped moisture can lead to mold and biological growth. The Tramex Skipper Plus can be moved across the surface of the boat to moisture survey in a fast and thorough manner, detecting moisture non-destructively through paint and coatings on wood up to a depth of 1.25". The Tramex Skipper Plus can also be used to detect leaks and trace them to source both above and below decks.

Please click on the links below for additional information on the models available for this product:

The Tramex SP200 Spare 7" Pins is used with Probe HH14SP200.

Please click on the links below for additional information on the models available for this product:

The Tramex SP52 Spare 1.5" Pins is used with Hammer Probe.

Please click on the links below for additional information on the models available for this product:

The Tramex SP90 Spare 3" Pins is used with Probe HH14SP90

Please click on the links below for additional information on the models available for this product:

The Tramex TP20 Spare Pins is used for PTM-Professional Pin Meter

Please click on the links below for additional information on the models available for this product:

The Tramex WDIK5.1 Water Damage Restoration Inspection Kit is a complete kit for moisture testing of concrete & wood flooring and numerous other building materials such as drywall, wood, plaster, brick, tiles, resilient flooring, laminates and roofing. Featuring the Tramex CMEX2 digital concrete moisture meter for testing per ASTM F2659 and the reusable Hygro-i probe for testing relative humidity, temperature and dew point in the environment, or performing ASTM F2170 (and ASTM F2420 with optional Hood) for relative humidity readings in concrete slabs. An infrared surface thermometer gives surface temperature and dew point conditions used in conjunction with the Hygro-i probe. A heavy-duty pin-probe measures Moisture Content in wood. The Tramex MEP allows for non-invasive testing of moisture conditions in numerous building materials such as drywall, wood, plaster, brick, tiles, resilient flooring, laminates and roofing. The Water Damage Restoration Inspection Kit comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex WDMK5.1 Water Damage Restoration Master Kitis theultimate Tramex kit for moisture testing of concrete & wood flooring and numerous other building materials such as drywall, wood, plaster, brick, tiles, resilient flooring, laminates and roofing. The Tramex WDMK5.1 features the Tramex CMEX2 digital concrete moisture meter for testing per ASTM F2659 and the reusable Hygro-i probe for testing relative humidity, temperature and dew point in the environment, or performing ASTM F2170 (and ASTM F2420 with optional Hood) for relative humidity readings in concrete slabs. An infrared surface thermometer gives surface temperature and dew point conditions used in conjunction with the Hygro-i probe. A heavy-duty pin-probe measures Moisture Content in wood. The Tramex MEP allows for non-invasive testing of moisture conditions in numerous building materials such as drywall, wood, plaster, brick, tiles, resilient flooring, laminates and roofing. The Water Damage Restoration Master Kit comes in a protective heavy-duty carrying case with die-cut foam lining.

Please click on the links below for additional information on the models available for this product:

The Tramex WDZK5.1 Water Damage Restoration EZ Kit is a compact kit for instant and precise non-destructive testing of moisture conditions in numerous building materials such as concrete and other cementitious materials per ASTM F2659, as well as drywall, wood, plaster, brick, tiles, resilient flooring, laminates and roofing. The Tramex WDZk5.1 features the the Tramex MEP non-destructive overall building inspection moisture meter, and the Tramex CME4 concrete moisture meter. The Water Damage Restoration EZ Kit comes in a Tramex Easy-travel case.

Please click on the links below for additional information on the models available for this product:

The Wagner C555 Concrete Moisture Meter provides fast, non-destructive preliminary moisture measurements on smooth, firm concrete to help pinpoint problem areas and determine where to place Rapid RH L6 Smart Sensors. With its built-in ambient sensors and included On-Demand Calibrator, the C555 comes with everything you need to perform the test as outlined in ASTM F2659.

Please click on the links below for additional information on the models available for this product:

The Wagner Meter Smart Logger is a discrete Bluetooth temperature and humidity data logger. Captures, records, and sends up to 12,000 readings or 300 days of ambient temperature and relative humidity data.

Please click on the links below for additional information on the models available for this product:

The Wagner Orion 910 Deep Depth Pinless Wood Moisture Meter Kit continues the Wagner tradition of superior accuracy and adds incredible new functionality. The new Orion 910 meter incorporates IntelliSense technology, a more rugged design, and industry - exclusive true in-the-field calibration capability provided by the included On-Demand Calibrator. The Wagner Orion 910 Deep Depth Pinless Wood Moisture Meter Kit features the Orion 910, which is designed to build upon the capabilities of the popular Wagner MMC220 meter it replaces. The Orion 910 takes moisture readings in your wood or other material from the surface down to .75 (19mm) in depth. A flexible rubber boot makes the 910 durable enough to withstand your toughest jobs. The Orion 910 joins the rest of the Orion line of meters in being the first in the industry to provide true in-the-field calibration capability with the included On-Demand Calibrator. Calibrate your Orion 910 at your location in about 30 seconds whenever you want. The Orion line of wood moisture meters continues Wagners 50-plus year tradition of providing accurate, dependable non-damaging pinless moisture measurement technology, measuring IN the wood not just ON the wood, and backed by Wagners industry-leading 7-year warranty.

Please click on the links below for additional information on the models available for this product:

The Wagner Orion 920 Shallow Depth Pinless Wood Moisture Meter Kit features the Orion 920 meter designed exclusively for shallow measurement of moisture content from the surface down to .25 (6.4mm) deep inside wood or other material. The Wagner Orion 920 Shallow Depth Pinless Wood Moisture Meter Kit is ideal for applications where accurate moisture readings from thin wood pieces or coatings are critical to success. The Orion 920 Shallow Depth Pinless Wood Moisture Meter Kit features the Orion 920, carrying the Wagner tradition of superior accuracy forward with added capabilities and usefulness. The 920 takes moisture readings in your wood from the surface down to .25 (6.4mm) in depth. A flexible rubber boot makes the 920 durable enough to withstand your toughest jobs. The Orion 920 joins the rest of the Orion line of meters in being the first in the industry to provide true in-the-field calibration capability with the included On-Demand Calibrator. Calibrate your Orion 920 at your location in about 30 seconds whenever you want. The Orion line of wood moisture meters continues Wagners 50-plus year tradition of providing accurate, dependable non-damaging pinless moisture measurement technology, measuring IN the wood not just ON the wood, and backed by Wagners industry-leading 7-year warranty.

Please click on the links below for additional information on the models available for this product:

The Wagner Orion 930 Dual Depth Pinless Wood Moisture Meter Kit features the Orion 930 meter, designed for measurement of moisture content from the surface down to .25 (6.4mm) or .75 (19mm) deep inside wood or other material. The Wagner Orion 930 Dual Depth Moisture Meter features the versatility that is needed for flooring, quality control, woodworking, and inspection applications. The Orion 930 Dual Depth Pinless Wood Moisture Meter Kit features the Orion 930, carrying the Wagner tradition of superior accuracy forward with the added versatility of dual depth measurement in wood or other materials. The 930 takes moisture readings in your wood from the surface down to .25 (6.4mm) in depth in the shallow mode or from the surface down to .75 (19mm) in the deep scan mode. A flexible rubber boot makes the 930 durable enough to withstand your toughest jobs. The Orion 930 joins the rest of the Orion line of meters in being the first in the industry to provide true in-the-field calibration capability with the included On-Demand Calibrator. Calibrate your Orion 930 at your location in about 30 seconds whenever you want. The Orion line of wood moisture meters continues Wagners 50-plus year tradition of providing accurate, dependable non-damaging pinless moisture measurement technology, measuring IN the wood not just ON the wood, and backed by Wagners industry-leading 7-year warranty.

Please click on the links below for additional information on the models available for this product:

The Wagner Orion 940 Data Collection Pinless Wood Moisture Meter Kit features the Orion 940 meter, designed for measurement of moisture content from the surface down to .25 (6.4mm) or .75 (19mm) deep inside wood or other materials. The Wagner Orion 940 Moisture Meter also features data collection and storage capabilities vital to Quality Control and home or property restoration applications. The Orion 940 Data Collection Pinless Wood Moisture Meter Kit features the Orion 940, carrying the Wagner tradition of superior accuracy forward with the added versatility of dual depth measurement and data collection. The Orion 940 can collect data in two modes, either manual or automatic, with viewable moisture stats. The Orion 940 can store up to 100 readings and includes high-low-average analysis. A flexible rubber boot makes the 940 durable enough to withstand your toughest jobs. The Orion 940 joins the rest of the Orion line of meters in being the first in the industry to provide true in-the-field calibration capability with the included On-Demand Calibrator. Calibrate your Orion 940 at your location in about 30 seconds whenever you want. The Orion line of wood moisture meters continues Wagners 50-plus year tradition of providing accurate, dependable non-damaging pinless moisture measurement technology, measuring IN the wood not just ON the wood, and backed by Wagners industry-leading 7-year warranty.

Please click on the links below for additional information on the models available for this product:

The Wagner Orion 950 Smart Pinless Wood Moisture Meter Kit is the all-in-one solution for busy professionals desiring superior accuracy and multi-tool functionality. The Wagner Orion 950 features an on-board Equilibrium Moisture Content (EMC) calculator, Bluetooth connectivity to free smart device apps, built-in temperature/RH sensor, and more. The Orion 950 Smart Pinless Wood Moisture Meter Kit features the Orion 950, carrying the Wagner tradition of superior accuracy forward with all of the features of the 910, 920, 930, and 940 meters and adding more. A flexible rubber boot makes the 950 durable enough to withstand your toughest jobs. The Orion 950 joins the rest of the Orion line of meters in being the first in the industry to provide true in-the-field calibration capability with the included On-Demand Calibrator. Calibrate your Orion 950 at your location in about 30 seconds whenever you want. The Orion line of wood moisture meters continues Wagners 50-plus year tradition of providing accurate, dependable non-damaging pinless moisture measurement technology, measuring IN the wood not just ON the wood, and backed by Wagners industry-leading 7-year warranty.

Please click on the links below for additional information on the models available for this product: